| |
| Airflow Guide |
RB2-9904-000CN |
Airflow Guide (duct) - Black plastic |
| |
|
insert piece which runs the width of the |
| |
|
printer and has an air flow hole on right |
| |
|
side - Directs air flow from the fan on |
| |
|
the left side of the printer to the |
| |
|
fusing assembly - Snap locks in center |
| |
|
rear of printer |
| |
| |
RB3-0025-000CN |
Airflow guide (duct) / fan holder bracket |
| |
|
assembly (Quartz Gray plastic) - Mounts |
| |
|
on the left metal side frame assembly |
| |
| Arm |
RB3-0089-000CN |
Top cover rack arm (Black) - Plastic arm |
| |
|
with teeth on bottom edge - Disengages |
| |
|
the imaging drum/transfer assembly drive |
| |
|
cams when the top door is open - Mounts |
| |
|
on the right side of the top cover door |
| |
| Belt |
RB1-8668-030CN |
Feed guide drive belt - Small belt |
| |
|
approximately 5/16 inch wide with 'A' |
| |
|
shaped ribs on it - Between the feed |
| |
|
drive roller and the small center roller |
| |
|
Driven via the transfer roller gear |
| |
|
train |
| |
| |
RB3-0063-000CN |
Paper feed belt - Small black rubber belt |
| |
|
approximately 1/8 inch wide with little |
| |
|
'A' shaped ribs on it - Goes between the |
| |
|
feed drive roller and the pulley rollers |
| |
|
(eight used) |
| |
| Bezel |
RB3-0035-000CN |
Interface bezel (Quartz Gray plastic) - |
| |
|
Vertical cover that surronds the |
| |
|
interface connectors - Mounts on the |
| |
|
right rear of the printer |
| |
| Body |
RG5-6915-030CN |
250 sheet cassette tray main body |
| |
|
assembly - Includes the main structure |
| |
|
frame, paper stops, lift plate, springs, |
| |
|
and the separation pad assembly - Does |
| |
|
NOT include the blue plastic front cover |
| |
|
- For the cassette on the 250 sheet input |
| |
|
tray assembly |
| |
| Bushing |
RB2-2895-000CN |
Shaft bushing/retainer - Right side |
| |
|
pickup roller support bushing - Mounts on |
| |
|
and retains the right end of the pickup |
| |
|
roller shaft - For the base on the 250 |
| |
|
sheet input tray assembly |
| |
| |
RB2-2896-000CN |
Shaft bushing/retainer - Left side pickup |
| |
|
roller support bushing - Mounts on and |
| |
|
retains the left end of the pickup roller |
| |
|
shaft - For the base on the 250 sheet |
| |
|
input tray assembly |
| |
| |
RB2-2897-000CN |
Shaft bushing/retainer - Mounts on the |
| |
|
gear side of the drive shaft for the |
| |
|
paper pickup roller assembly - For the |
| |
|
base on the 250-sheet input tray assembly |
| |
| |
RB2-2973-000CN |
Support bushing - Mounts on each end of |
| |
|
the pressure roller in the fusing |
| |
|
assembly |
| |
| |
RB2-3043-000CN |
Left roller bushing - Acts as the bearing |
| |
|
and retainer for the left end of the |
| |
|
paper pickup roller assembly (tray 1) - |
| |
|
Mounts on the left side of the front |
| |
|
frame assembly |
| |
| |
RB2-3044-000CN |
Right roller bushing - Acts as the |
| |
|
bearing and retainer for the right end of |
| |
|
the paper pickup roller assembly (tray 1) |
| |
|
Mounts on the right side of the front |
| |
|
frame assembly |
| |
| |
RB2-9808-000CN |
Bushing/shaft retainer assembly - Black |
| |
|
plastic - Holds the rotation drive shaft |
| |
|
in the right side plate of the toner |
| |
|
cartridge carousel (rotary) assembly |
| |
| |
RB2-9809-000CN |
Bushing/shaft retainer assembly (White |
| |
|
plastic) - Holds the rotation drive shaft |
| |
|
in the left side plate of the toner |
| |
|
cartridge carousel (rotary) assembly |
| |
| |
RB3-0014-000CN |
Bushing assembly (black plastic bushing |
| |
|
with small guide roller on top) - Holds |
| |
|
the right end of the transfer roller |
| |
|
assembly in the bottom frame assmebly |
| |
| |
RS5-1635-000CN |
Shaft bushing - For the paper pickup |
| |
|
clutch gear shaft - Mounts on the plate |
| |
|
of the multipurpose paper pickup gear |
| |
|
assembly |
| |
| |
RS5-1636-000CN |
Shaft bushing - Mounts on the gear end of |
| |
|
the feed roller shaft in the base on the |
| |
|
250-sheet input tray assembly |
| |
| |
RS5-1637-000CN |
Bushing (black plastic) - Mounts on the |
| |
|
right end of the registration roller |
| |
|
assembly |
| |
| |
RS5-1638-000CN |
Bushing - For the registration roller |
| |
|
gear drive shaft on the right side of the |
| |
|
front frame assembly, and the left side |
| |
|
of the feed roller in the 250-sheet paper |
| |
|
input tray assembly |
| |
| Cable |
C9706-60104 |
Flat flexible cable - From DC controller |
| |
|
board to formatter board |
| |
| |
RG5-6971-000CN |
Cable assembly (two 3-pin connectors and |
| |
|
a spad lug) - Power cable for the fusing |
| |
|
assembly - From fusing assembly connector |
| |
|
to the chassis ground and the low voltage |
| |
|
power supply board |
| |
| |
RG5-6974-000CN |
Cable assembly - From toner cartridge |
| |
|
E-label reader assembly on the carousel |
| |
|
to the DC controller board |
| |
| |
RG5-7106-000CN |
Cable assembly (two 2-pin connectors) - |
| |
|
Connects between the low voltage power |
| |
|
supply board (J401) and the formatter |
| |
|
board (J1003) |
| |
| |
RG5-7107-000CN |
Cable assembly (8-pin, red wire) - (J402 |
| |
|
to J134) connects the low voltage power |
| |
|
supply board to the DC controller board |
| |
| |
RG5-7108-000CN |
Cable assembly (two 8-pin connectors, |
| |
|
Purple wire) - Connects between the low |
| |
|
voltage power supply board (J403) and the |
| |
|
DC controller board (J133) |
| |
| |
RG5-7109-000CN |
Cable assembly (two 7-pin connectors) - |
| |
|
Connects between the DC controller board |
| |
|
(J119) and the fusing assembly connector |
| |
|
(J201) |
| |
| |
RG5-7114-000CN |
Cable assembly (two 4-pin connectors) |
| |
|
with shield - Connects between the |
| |
|
cartridge drive motor (J705) the DC |
| |
|
controller board (J106) |
| |
| |
RG5-7115-000CN |
Cable assembly (two 3-pin connectors) - |
| |
|
Connects between the roller engaging |
| |
|
photosensor (J714) and the DC controller |
| |
|
board (J115) |
| |
| |
RG5-7117-000CN |
Cable assembly (two 3-pin connectors) - |
| |
|
Connects between the engaging sensor |
| |
|
(J712) on the toner cartridge carousel |
| |
|
and the DC controller board (J125) |
| |
| |
RG5-7122-000CN |
Cable assembly - 'Y' type cable (three |
| |
|
connectors) - The 14-pin connector splits |
| |
|
into an 8-pin connector and a 6-pin |
| |
|
connector - Connects between the DC |
| |
|
controller board (J118) and the optional |
| |
|
paper tray connectors (J230) |
| |
| |
RG5-7123-000CN |
Grounding cable assembly - Connects from |
| |
|
the optional tray connector housing to |
| |
|
the metal right side frame assembly |
| |
| |
RG5-7126-000CN |
Cable assembly (two 5-pin connectors) - |
| |
|
Connects between the sub-high voltage |
| |
|
board (J505) and the high voltage board |
| |
|
(J503) |
| |
| |
RG5-7128-000CN |
Cable assembly (four 3-pin connectors) - |
| |
|
Connects between the DC controller board |
| |
|
(J107 and J138) and the leading edge |
| |
|
paper sensor for the fusing assembly |
| |
|
(J720) and the registration sensor (J711) |
| |
| |
RG5-7129-000CN |
Cable assembly (two connectors and two |
| |
|
spade lugs) - From toner cartridge |
| |
|
contacts on the left carousel side plate |
| |
|
to the cable (J512 and J511) that runs to |
| |
|
the high voltage power supply board |
| |
| |
RG5-7130-000CN |
High voltage cable assembly - Connects |
| |
|
between the high voltage board spring |
| |
|
contacts (on the middle frame assembly) |
| |
|
and the cables for the toner cartridge |
| |
|
carousel left plate assembly (J511 and |
| |
|
J512) |
| |
| |
RG5-7138-000CN |
Cable assembly - From sensor (PS717) |
| |
|
(which senses paper feeding from optional |
| |
|
tray 3) to the small interconnecting PC |
| |
|
board on the right side frame/cover |
| |
|
assembly - For the base on the 250-sheet |
| |
|
input tray assembly |
| |
| |
RG5-7139-000CN |
Cable assembly - From paper out sensor |
| |
|
(PS716) to the small interconnecting PC |
| |
|
board on the right side frame/cover |
| |
|
assembly - For the base on the 250-sheet |
| |
|
input tray assembly |
| |
| |
RG5-7144-000CN |
Cable assembly (with seven connectors) - |
| |
|
From various upper level components to |
| |
|
the DC controller board |
| |
| |
RG5-7145-000CN |
Front cable assembly (six connectors) - |
| |
|
From various components on the front |
| |
|
frame assembly and right side to the DC |
| |
|
controller board |
| |
| |
RG5-7146-000CN |
High voltage cable assembly (two 15-pin |
| |
|
connectors and two 14-pin connectors) - |
| |
|
Connects between the high voltage power |
| |
|
supply board (J501 and J502) and the DC |
| |
|
controller board (J136 and J135) |
| |
| |
RG5-7149-000CN |
Connector assembly - Includes the 14-pin |
| |
|
(F) interface connector and cable |
| |
|
assembly - (Tray 2 to printer connector) |
| |
|
connects to the feed drive PC board in |
| |
|
the cassette base assembly |
| |
| |
RH2-5524-000CN |
Flat flexible cable (FFC) assembly - |
| |
|
Connects between the laser/scanner |
| |
|
assembly (J11) the DC controller board |
| |
|
(J102) |
| |
| Cable (Interface) |
C2950A |
IEEE 1284 Bi-Tronics parallel cable - |
| |
|
DB-25 (M) connector (type A) to 36-pin |
| |
|
Centronics (M) connector (type B) - 2.0m |
| |
|
(6.6ft) long |
| |
| |
C2951A |
IEEE-1284 Bi-Tronics parallel cable - |
| |
|
DB-25 (M) connector (type A) to 36 pin |
| |
|
Centronics (M) connector (type B) - 3.0m |
| |
|
(9.8ft) long |
| |
| |
C6518A |
Universal serial bus (USB) interface |
| |
|
cable - Type 'A' connector to type 'B' |
| |
|
connector - 2.0m (6.6ft) long |
| |
| Carousel |
RG5-6910-080CN |
Carousel (Rotary) assembly - Includes the |
| |
|
carousel assembly, the support assembly, |
| |
|
end plates, drive gears and shaft, |
| |
|
sensors, and cables - Mounts towards the |
| |
|
rear of the printer in front of the rear |
| |
|
frame assembly |
| |
| Cartridge |
C9700A |
HP Color LaserJet smart Black print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9701A |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9702A |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9703A |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9700-67901 |
HP Color LaserJet smart Black print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9701-67901 |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9702-67901 |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| |
C9703-67901 |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages at 5% coverage |
| |
| Cleaning Supplies |
5090-3379 |
Toner cleaning cloth - Specially treated |
| |
|
cloth for absorbing toner (1 per package) |
| |
|
Ideal For clening up toner spills |
| |
| Clip |
WT2-5056-000CN |
Cable clip - 'C' shaped White plastic - |
| |
|
Mounts in the opening on the cover for |
| |
|
the paper pickup solenoid |
| |
| |
WT2-5737-000CN |
Cable clip - Mounts on the bottom pan of |
| |
|
the printer (two used) |
| |
| |
XD2-1100-502CN |
E-ring clip - Secures the dual gear to |
| |
|
the drive shaft which drives the |
| |
|
registration roller - Located on the |
| |
|
inside of the front frame assembly |
| |
| |
XD9-0136-000CN |
Retaining E-ring - Mounts on the left end |
| |
|
of the paper feed roller assembly - For |
| |
|
the base on the 250 sheet input tray |
| |
|
assembly |
| |
| Clutch |
RH7-5366-000CN |
Electromagnetic clutch assembly (24V) - |
| |
|
Electrical clutch between the clutch |
| |
|
drive gear and shaft - (CL2) Engages the |
| |
|
roller within the imaging drum/transfer |
| |
|
assembly from the main gear train |
| |
| Connector |
RH2-5519-000CN |
Connector assembly - For optional paper |
| |
|
tray - One mounts to the bottom right |
| |
|
side of the printer middle frame assembly |
| |
|
(interfaces 250 sheet tray), and the |
| |
|
other to the bottom of the 250 sheet tray |
| |
|
base assembly (interfaces 500 sheet tray) |
| |
|
(two used) |
| |
| |
RH2-5520-000CN |
Connector for the fusing assembly - Seven |
| |
|
small contol pins plus three separated |
| |
|
high current pins - Mounts in the |
| |
|
connector housing mounted on the bottom |
| |
|
pan of the printer |
| |
| Control Panel |
RG5-6927-000CN |
Control panel assembly (mechanical only) |
| |
|
- Includes the 'Rotate Carousel', 'Cancel |
| |
|
Job' and the 'Go' buttons, plus the |
| |
|
various indicator light pipes - All |
| |
|
switches and LED's are on the formatter |
| |
|
PC board - Mounts to the top of the right |
| |
|
cover assembly |
| |
| Cover |
RB3-0030-000CN |
Upper rear cover (Quartz Gray) - Mounts |
| |
|
on the upper rear of the printer above |
| |
|
the face-up output tray door |
| |
| |
RB3-0032-000CN |
Face-down paper output L-Shaped cover ( |
| |
|
Blue) - Serves as the rear of the tray |
| |
|
for the face-down output tray on top of |
| |
|
the printer |
| |
| |
RB3-0052-000CN |
Gear Cover (Small Black plastic cover) - |
| |
|
Covers the left end of the feed drive |
| |
|
shaft - Mounts towards the left side of |
| |
|
the middle frame assembly |
| |
| |
RB3-0102-000CN |
Front inner cover (Blue) - Mounts on the |
| |
|
front frame above the multi-purpose input |
| |
|
tray |
| |
| |
RB3-0103-000CN |
Front lower cover (blue plastic) - Front |
| |
|
lower strip below the multi-purpose input |
| |
|
tray - Has recessed area for the printer |
| |
|
logo |
| |
| |
RB3-0104-000CN |
Roller cover - Covers the multipurpose |
| |
|
paper pickup roller assembly - Mounts on |
| |
|
the lower front of the front frame |
| |
|
assembly |
| |
| |
RB3-0106-000CN |
Left side frame/cover (Quartz Gray) |
| |
|
plastic - Left side cover and input paper |
| |
|
tray guide |
| |
| |
RB3-0109-000CN |
Front cover for the 250 sheet paper |
| |
|
cassette tray (Blue) plastic - Has molded |
| |
|
in paper loading instructions and a '2' |
| |
|
on the front |
| |
| |
RB3-0120-000CN |
Solenoid cover (Steel) - For magnetic |
| |
|
wave sheilding |
| |
| |
RB3-0165-000CN |
Top inner cover (black plastic) - Covers |
| |
|
the back half of the pressure roller arms |
| |
|
and springs - For the base on the |
| |
|
250-sheet input tray assembly |
| |
| |
RB3-0166-000CN |
Bottom inner cover (Black) plastic - One |
| |
|
covers the paper feed sensor in the |
| |
|
center and the other covers sensor wires |
| |
|
toward the right side - Mounts on the |
| |
|
bottom of the center frame assembly of |
| |
|
the 250-sheet input tray assembly (two |
| |
|
used) |
| |
| |
RB3-0282-000CN |
Inner cover - Covers the small |
| |
|
interconnecting PC board - Mounts on top |
| |
|
of the right side support frame/cover |
| |
|
assemly on the base of the 250-sheet |
| |
|
feeder assembly |
| |
| |
RB3-0283-000CN |
Inner cover - Covers the bottom of the |
| |
|
connector that interconnects the input |
| |
|
tray base to the printer - Mounts on the |
| |
|
bottom of the right side support |
| |
|
frame/cover assembly for the base of the |
| |
|
250-sheet tray assembly |
| |
| |
RG5-6900-000CN |
Top cover assembly (blue plastic) - |
| |
|
Includes the molded-in face-down output |
| |
|
tray and the lift-up top cover door |
| |
|
assembly |
| |
| |
RG5-6919-000CN |
Right side frame/cover assembly (Quartz |
| |
|
Gray) plastic - Includes the right side |
| |
|
cover and paper tray guide, the cassette |
| |
|
retainer spring, tray 3 connector, |
| |
|
printer interface connector, and rubber |
| |
|
feet |
| |
| |
RG5-6953-000CN |
Right side cover assembly (Quartz Gray) |
| |
|
plastic - Includes the DIMM memory door |
| |
| |
RG5-6902-000CN |
Left side cover assembly (Quartz Gray) |
| |
|
plastic - Includes the power switch |
| |
|
button, rod and spring (The power switch |
| |
|
is located on the low voltage power |
| |
|
supply board) |
| |
| |
RB3-0028-000CN |
Left side cover (Quartz Gray) - Does not |
| |
|
include any attaching parts |
| |
| Cross-Brace |
RB3-0108-000CN |
Metal support cross-brace - Mounts on the |
| |
|
top rear of the left and right support |
| |
|
frame/cover assemblies - For the base on |
| |
|
the 250-sheet input tray assembly |
| |
| Damper |
RB2-6248-000CN |
Damper assembly (Gray plastic piece with |
| |
|
small 13-tooth gear on it) - Helps to |
| |
|
reduce clunking when the paper pickup |
| |
|
roller is engaged - Engages the paper |
| |
|
pickup roller - Mounts on the right side |
| |
|
of the front frame assembly |
| |
| Door |
RB3-0033-000CN |
Memory access door (Quartz Gray |
| |
|
perforated plastic) - Allows access to |
| |
|
the printer memory slots - Mounts on the |
| |
|
right side cover |
| |
| |
RF5-4007-000CN |
Top cover door (blue plastic) - For |
| |
|
accessing the toner cartridges and the |
| |
|
imaging drum/transfer assembly - Mounts |
| |
|
to the top cover frame |
| |
| Drive Assembly |
RG5-6911-000CN |
Rotary drive assembly - Includes the |
| |
|
carousel rotating motor (DCM703), toner |
| |
|
cartridge drive motor (PM705), developing |
| |
|
rotary stopper solenoid (SL93), bracket, |
| |
|
and gears - Rotates the toner cartridge |
| |
|
carousel (DCM703) and provides drive for |
| |
|
toner operatio |
| |
| Drum |
C9704A |
Imaging drum/transfer assembly cartridge |
| |
|
Inserts into printer through the top |
| |
|
door - Life expectancy is 20,000 pages |
| |
|
for black print only, 5,000 pages for |
| |
|
color (Typical combined life is |
| |
|
approximately 6,000 to 8,000 pages) |
| |
| |
C9704-67901 |
Imaging drum/transfer assembly cartridge |
| |
|
Inserts into printer through the top |
| |
|
door - Life expectancy is 20,000 pages |
| |
|
for black print ONLY, 5,000 pages for |
| |
|
color (Typical combined life is |
| |
|
approximately 6,000 to 8,000 pages) |
| |
| Fan |
RH7-1537-000CN |
Cooling fan (Panaflo Model FBA08T24H - |
| |
|
80mm X 80mm X 15mm high, DC brushless, |
| |
|
24V DC, 190mA) - (FM712) Mounts in the |
| |
|
airflow guide/fan bracket assembly on the |
| |
|
left side of the printer |
| |
| Flag |
RB2-9925-000CN |
Sensor arm and flag - Activates the |
| |
|
photosensor (Does NOT include the roller) |
| |
|
For the Leading edge paper sensor For |
| |
|
the fusing assembly (PS720) - Protrudes |
| |
|
up through the feed plate on the middle |
| |
|
frame assembly |
| |
| |
RB3-0111-000CN |
Paper flag - Plastic rod with paper |
| |
|
sensing flag on one end and sensor |
| |
|
activator flag on the other - Senses |
| |
|
paper coming from the multi-purpose front |
| |
|
input tray (tray 1) |
| |
| |
RB3-0130-000CN |
Shaft mounted sensor flag (black plastic) |
| |
|
For the paper out sensor - Mounts on |
| |
|
the paper pickup roller drive shaft - For |
| |
|
the base on the 250-sheet input tray |
| |
|
assembly |
| |
| |
RB3-0132-000CN |
Mechanical sensor flag (black plastic) - |
| |
|
For the paper feed sensor - Mounts on top |
| |
|
of the center frame assembly - For the |
| |
|
base on the 250-sheet input tray assembly |
| |
| |
RB3-0135-000CN |
Test print flag (Black lever) - Used to |
| |
|
activate the print engine test switch - |
| |
|
Mounts in a metal holder in the upper |
| |
|
left of the front frame assembly |
| |
| Foot |
RB2-6297-000CN |
Rubber foot - Square self-adhesive rubber |
| |
|
foot - Attaches to the rear of the middle |
| |
|
frame assembly (two used) |
| |
| Frame |
RB3-0105-020CN |
Center support frame (black plastic) - |
| |
|
Support structure for the paper pickup |
| |
|
roller, feed roller, and paper sensors - |
| |
|
Mounts to the top front of both of the |
| |
|
support frame/cover assemblies on the |
| |
|
base of the 250-sheet input tray assembly |
| |
| Fusing Assembly |
RG5-6903-000CN |
Fusing assembly (For 110V to 127V |
| |
|
operation) - Bonds the toner to the paper |
| |
|
with heat - Slides in and locks in lower |
| |
|
rear of printer |
| |
| |
RG5-6913-000CN |
Fusing assembly (For 220V to 240V |
| |
|
operation) - Bonds the toner to the paper |
| |
|
with heat - Slides in and locks in lower |
| |
|
rear of printer |
| |
| Gear |
RB3-0022-000CN |
22 tooth gear (Black plastic) - Small |
| |
|
gear with diagonally cut teeth - Idler |
| |
|
gear between the transfer roller assembly |
| |
|
and the feed drive shaft - Mounts on the |
| |
|
left side of the middle frame assembly |
| |
| |
RB3-0091-000CN |
16 tooth gear (Black plastic) - Gear with |
| |
|
large stop tooth and shaft lock tab - |
| |
|
Used as part of the mechanism to |
| |
|
disengage the drive cams for the imaging |
| |
|
drum/transfer assembly - Mounts on the |
| |
|
inside of the right side metal chassis |
| |
|
assembly |
| |
| |
RB3-0092-000CN |
15 tooth gear with drive shaft (Black |
| |
|
plastic) - Used as part of the mechanism |
| |
|
to disengage the drive cams for the |
| |
|
imaging drum/transfer assembly - Mounts |
| |
|
on the right side metal chassis frame |
| |
| |
RS7-0418-000CN |
26 tooth gear (Black plastic) - Has 1/8th |
| |
|
portion of gear cut away - Mounts on the |
| |
|
end of the paper pickup roller for the |
| |
|
multipurpose input tray (Tray 1) |
| |
| |
RS7-0424-000CN |
Dual gear - 20 tooth / 40 tooth - Mounts |
| |
|
between the right side of the front frame |
| |
|
assembly and the paper pickup gear plate |
| |
|
assembly |
| |
| |
RS7-0425-000CN |
30 tooth gear (White plastic) - Part of |
| |
|
the drive gears for the registration |
| |
|
roller - Mounts on inside of the front |
| |
|
frame assembly on the right side |
| |
| |
RS7-0426-000CN |
Dual gear - 26 tooth / 50 tooth (White |
| |
|
plastic) - Part of the drive gears for |
| |
|
the registration roller - Mounts on |
| |
|
inside of the front frame assembly on the |
| |
|
right side |
| |
| |
RS7-0428-000CN |
30 tooth gear (White plastic) - Mounts on |
| |
|
the end of the registration roller drive |
| |
|
shaft |
| |
| |
RS7-0429-000CN |
26 tooth gear (White plastic) - Has |
| |
|
recess for shaft drive pin - Paper pickup |
| |
|
clutch drive gear - Mounts between the |
| |
|
right side of the front fame assembly and |
| |
|
the paper pickup gear plate assembly |
| |
| |
RS7-0430-000CN |
26 tooth gear - White gear with 1/8th |
| |
|
portion of gear cut away and pin for |
| |
|
spring tensioning - Mounts on the end of |
| |
|
the paper pickup roller in the base on |
| |
|
the 250-sheet input tray assembly |
| |
| |
RS7-0431-000CN |
15 tooth Gear (white plastic) - Mounts on |
| |
|
the end of the feed roller shaft in the |
| |
|
base on the 250-sheet input tray assembly |
| |
| |
RS7-0435-000CN |
Dual gear - 32 tooth / 37 tooth (White |
| |
|
plastic) - Drives the upper top bin |
| |
|
output roller - Mounts on the right side |
| |
|
of the rear frame assembly |
| |
| |
RS7-0436-000CN |
Dual gear - 37 tooth / 43 tooth (White |
| |
|
plastic) - Part of the gear train for |
| |
|
driving the upper top bin output roller - |
| |
|
Mounts on the right side of the rear |
| |
|
frame assembly |
| |
| |
RS7-0437-000CN |
51 tooth gear (White plastic) - Main |
| |
|
drive gear for both the upper and lower |
| |
|
top bin output rollers |
| |
| Gear Assembly |
RG5-6938-000CN |
Gear assembly - Metal plate with two |
| |
|
White plastic gears attached - Part of |
| |
|
the drive gears for the paper pickup |
| |
|
roller for the multipurpose input tray |
| |
|
(tray 1) - Mounts on the right side of |
| |
|
the front frame assembly |
| |
| Ground Plane |
RB2-9942-000CN |
Grounding plate - Provides grounding for |
| |
|
the top-of-page sensor and shielding for |
| |
|
the density sensor boards - Mounts on the |
| |
|
top left of the front frame assembly |
| |
| |
RB3-0119-000CN |
Grounding plate - Grounds the paper |
| |
|
pickup solenoid cover to the right side |
| |
|
metal chassis |
| |
| |
RB3-0137-000CN |
Grounding plate - Grounds the paper feed |
| |
|
roller - Mounts towards the right end of |
| |
|
the center frame assembly - For the base |
| |
|
on the 250-sheet input tray assembly |
| |
| Guide |
RB2-9903-000CN |
Cable guide (Quartz Gray plastic) - |
| |
|
Protects and supports the upper cable |
| |
|
assembly - Mounts to the right rear on |
| |
|
the laser/scanner support assembly |
| |
| |
RB2-9912-000CN |
Top output bin guide - Small curved |
| |
|
ribbed black plastic piece - Snaps on the |
| |
|
rear of the printer just below the upper |
| |
|
top bin output roller (two used) |
| |
| |
RB2-9954-000CN |
Left paper feed guide (small Black |
| |
|
plastic arm) - Mounts to the left of the |
| |
|
separation pad assembly on the lower |
| |
|
front frame assembly |
| |
| |
RB2-9955-000CN |
Right paper feed guide (small Black |
| |
|
plastic arm) - Mounts to the right of the |
| |
|
separation pad assembly on the lower |
| |
|
front frame |
| |
| |
RF5-4049-000CN |
Entrance guide assembly - Angled metal |
| |
|
guide between the registration roller and |
| |
|
the transfer roller - Mounts to the |
| |
|
bottom frame assembly |
| |
| |
RG5-6929-000CN |
Separation guide assembly - Includes the |
| |
|
plastic guide, label, and the two small |
| |
|
spring loaded rollers - Mounts in the |
| |
|
fusing assembly |
| |
| |
RG5-6930-000CN |
Lower separation guide assembly - |
| |
|
Includes the guide bracket, paper output |
| |
|
sensor (PS1) and flag, exit drive shaft |
| |
|
with two rubber rollers, shaft gear, and |
| |
|
idler gear - Mounts in the lower rear on |
| |
|
the fusing assembly |
| |
| |
RG5-6951-000CN |
Paper guide assembly - Paper width |
| |
|
adjustable guide assembly for the |
| |
|
multi-purpose front input tray (tray 1) - |
| |
|
Mounts with the two hinges on the lower |
| |
|
portion of the front frame assembly |
| |
| Hinge |
RB2-3041-000CN |
Tray hinge - For the left side of the |
| |
|
multi-purpose front input tray (tray one) |
| |
| |
RB2-3042-000CN |
Tray hinge - For the right side of the |
| |
|
multi-purpose front input tray (tray one) |
| |
| Holder |
RB2-9924-000CN |
Sensor assembly mounting holder - Holds |
| |
|
the leading edge paper sensor (PS720) for |
| |
|
the fusing assembly - Mounts on the |
| |
|
underside left on the middle frame |
| |
|
assembly |
| |
| |
RB3-0006-000CN |
Holder - Housing for the fusing connector |
| |
|
assembly - Mounts on the lower base pan |
| |
|
of the printer mechanism |
| |
| |
RB3-0023-000CN |
Interlock switch holder (Quartz Gray |
| |
|
plastic) - Does NOT include the |
| |
|
micro-switch - Mounts on the support |
| |
|
shelf for the laser/scanner assembly |
| |
|
(just to the left of the laser/scanner |
| |
|
assembly) |
| |
| Hook |
RB1-2190-000CN |
Pickup roller spring hook - Clips on the |
| |
|
pin of the drive gear for the pickup |
| |
|
roller and hooks the tensioning spring - |
| |
|
For the base on the 250-sheet input tray |
| |
|
assembly |
| |
| Insulator |
RB3-0007-000CN |
Insulating sheet (Transparent plastic) - |
| |
|
Mounts between the bottom pan and the |
| |
|
high and low voltage power supply boards |
| |
| |
RB3-0056-000CN |
Insulating sheet (Transparent plastic) - |
| |
|
Mounts to the underside of the middle |
| |
|
frame assembly |
| |
| Interface (Product) |
J3110A |
Ethernet 10Base-T (RJ-45) EIO network |
| |
|
internal print server PC board |
| |
| |
J3111A |
Ethernet 10Base-T/10Base2 and LocalTalk |
| |
|
(RJ-45, BNC, LocalTalk) EIO network PCA |
| |
| |
J4135A |
JetDirect connectivity card - Has one USB |
| |
|
port, one serial (DB9) port, and one |
| |
|
LocalTalk port - Plugs in one of the EIO |
| |
|
slots on selected DesignJet and LaserJet |
| |
|
printers |
| |
| |
J4167A |
JetDirect 610N token ring LAN interface |
| |
|
board - DB-9 and RJ-45 connectors |
| |
| |
J6057A |
JetDirect 615N internal print server LAN |
| |
|
interface board - 10Base-T and 100Base-TX |
| |
|
Plugs into peripheral EIO slot, has |
| |
|
RJ-45 connector - Includes software on |
| |
|
CD-ROM and manual |
| |
| |
J6057AR |
JetDirect 615N internal print server |
| |
|
(10Base-T and 100Base-TX) LAN interface |
| |
|
board - Plugs into peripheral EIO slot - |
| |
|
Has a RJ-45 connector - Comes with |
| |
|
software on CD-ROM and manual |
| |
| |
J6058A |
JetDirect 680N internal wireless |
| |
|
IEEE-802.11b (Wi-Fi) print server - Plugs |
| |
|
into peripheral EIO slot |
| |
| Label |
RS6-8662-000CN |
Image cartridge label - Shows the imaging |
| |
|
drum/transfer assembly removal steps - |
| |
|
Mounts on the right side of the front |
| |
|
inner cover (Visible when the top cover |
| |
|
is lifted) |
| |
| Laser/Scanner |
RG5-6880-000CN |
Laser/scanner assembly - Mounts in the |
| |
|
center of the scanner support assembly |
| |
| Lever |
RB3-0178-000CN |
Right side lock release lever - Part of |
| |
|
locking system used to secure the fusing |
| |
|
assembly in the printer |
| |
| |
RB3-0179-000CN |
Left side lock release lever - Part of |
| |
|
locking system used to secure the fusing |
| |
|
assembly in the printer |
| |
| Manual |
5851-1468 |
LaserJet printer family paper |
| |
|
specification guide |
| |
| |
C9706-90926 |
HP Color LaserJet 2500 series service |
| |
|
manual |
| |
| Memory (Product) |
C7845A |
32MB, 100-pin SDRAM DIMM memory module |
| |
| |
C7846A |
64MB SDRAM - 100MHz synchronous DRAM - |
| |
|
DIMM package |
| |
| |
C9121A |
128MB, 100-pin SDRAM DIMM memory module |
| |
| Motor |
RF5-4010-000CN |
Main motor assembly - Large motor mounted |
| |
|
on a controller PC board - Mounts on the |
| |
|
inside of the metal right side frame |
| |
|
assembly |
| |
| |
RG5-6958-000CN |
Rotary motor assembly - (DCM703) Rotates |
| |
|
the four color toner cartridges in the |
| |
|
carousel to position one of them for |
| |
|
printing |
| |
| |
RH7-1533-000CN |
Stepping motor - 24V DC - (PM704) |
Login Here
