| |
| Airflow Guide |
RB2-9904-000CN |
Airflow Guide (duct) - Black plastic |
| |
|
insert piece which runs the width of the |
| |
|
printer and has an air flow hole on right |
| |
|
side - Directs air flow from the fan on |
| |
|
the left side of the printer to the |
| |
|
fusing assembly - Snap locks in center |
| |
|
rear of printer |
| |
| |
RB9-0901-000CN |
Airflow guide (duct) / fan holder bracket |
| |
|
assembly (Alloy Gray plastic) - Mounts on |
| |
|
the left metal side frame assembly |
| |
| Arm |
RB3-0089-000CN |
Top cover rack arm (Black) - Plastic arm |
| |
|
with teeth on bottom edge - Disengages |
| |
|
the imaging drum/transfer assembly drive |
| |
|
cams when the top door is open - Mounts |
| |
|
on the right side of the top cover door |
| |
| Belt |
RB1-8668-030CN |
Feed guide drive belt - Small belt |
| |
|
approximately 5/16 inch wide with 'A' |
| |
|
shaped ribs on it - Between the feed |
| |
|
drive roller and the small center roller |
| |
|
Driven via the transfer roller gear |
| |
|
train |
| |
| |
RB3-0063-000CN |
Paper feed belt - Small black rubber belt |
| |
|
approximately 1/8 inch wide with little |
| |
|
'A' shaped ribs on it - Goes between the |
| |
|
feed drive roller and the pulley rollers |
| |
|
(eight used) |
| |
| Bushing |
RB2-3043-000CN |
Left roller bushing - Acts as the bearing |
| |
|
and retainer for the left end of the |
| |
|
paper pickup roller assembly (tray 1) - |
| |
|
Mounts on the left side of the front |
| |
|
frame assembly |
| |
| |
RB2-3044-000CN |
Right roller bushing - Acts as the |
| |
|
bearing and retainer for the right end of |
| |
|
the paper pickup roller assembly (tray 1) |
| |
|
Mounts on the right side of the front |
| |
|
frame assembly |
| |
| |
RB2-9809-000CN |
Bushing/shaft retainer assembly (White |
| |
|
plastic) - Holds the rotation drive shaft |
| |
|
in the left side plate of the toner |
| |
|
cartridge carousel (rotary) assembly |
| |
| |
RB3-1094-000CN |
Bushing assembly (Black plastic bushing |
| |
|
with small guide roller on top) - Holds |
| |
|
the right end of the transfer roller |
| |
|
assembly in the middle frame assmebly |
| |
| |
RB9-0879-000CN |
Bushing/shaft retainer assembly (Black |
| |
|
plastic) - Holds the rotation drive shaft |
| |
|
in the right side plate of the toner |
| |
|
cartridge carousel (rotary) assembly |
| |
| |
RS5-1635-000CN |
Shaft bushing - For the paper pickup |
| |
|
clutch gear shaft - Mounts on the plate |
| |
|
of the multipurpose paper pickup gear |
| |
|
assembly |
| |
| |
RS5-1637-000CN |
Bushing (black plastic) - Mounts on the |
| |
|
right end of the registration roller |
| |
|
assembly |
| |
| |
RS5-1638-000CN |
Bushing - For the registration roller |
| |
|
gear drive shaft - Mounts on the right |
| |
|
side of the front frame assembly |
| |
| Cable |
RG5-6971-000CN |
Cable assembly (two 3-pin connectors and |
| |
|
a spad lug) - Power cable for the fusing |
| |
|
assembly - From fusing assembly connector |
| |
|
to the chassis ground and the low voltage |
| |
|
power supply board |
| |
| |
RG5-7106-000CN |
Cable assembly (two 2-pin connectors) - |
| |
|
Connects between the low voltage power |
| |
|
supply board (J401) and the formatter |
| |
|
board (J1003) |
| |
| |
RG5-7108-000CN |
Cable assembly (two 8-pin connectors, |
| |
|
Purple wire) - Connects between the low |
| |
|
voltage power supply board (J403) and the |
| |
|
DC controller board (J133) |
| |
| |
RG5-7109-000CN |
Cable assembly (two 7-pin connectors) - |
| |
|
Connects between the DC controller board |
| |
|
(J119) and the fusing assembly connector |
| |
|
(J201) |
| |
| |
RG5-7114-000CN |
Cable assembly (two 4-pin connectors) |
| |
|
with shield - Connects between the |
| |
|
cartridge drive motor (J705) the DC |
| |
|
controller board (J106) |
| |
| |
RG5-7115-000CN |
Cable assembly (two 3-pin connectors) - |
| |
|
Connects between the roller engaging |
| |
|
photosensor (J714) and the DC controller |
| |
|
board (J115) |
| |
| |
RG5-7117-000CN |
Cable assembly (two 3-pin connectors) - |
| |
|
Connects between the engaging sensor |
| |
|
(J712) on the toner cartridge carousel |
| |
|
and the DC controller board (J125) |
| |
| |
RG5-7122-000CN |
Cable assembly - 'Y' type cable (three |
| |
|
connectors) - The 14-pin connector splits |
| |
|
into an 8-pin connector and a 6-pin |
| |
|
connector |
| |
| |
RG5-7123-000CN |
Grounding cable assembly - Connects from |
| |
|
the optional tray connector housing to |
| |
|
the metal right side frame assembly |
| |
| |
RG5-7126-000CN |
Cable assembly (two 5-pin connectors) - |
| |
|
Connects between the sub-high voltage |
| |
|
board (J505) and the high voltage board |
| |
|
(J503) |
| |
| |
RG5-7128-000CN |
Cable assembly (four 3-pin connectors) - |
| |
|
Connects between the DC controller board |
| |
|
(J107 and J138) and the leading edge |
| |
|
paper sensor for the fusing assembly |
| |
|
(J720) and the registration sensor (J711) |
| |
| |
RG5-7129-000CN |
Cable assembly (two connectors and two |
| |
|
spade lugs) - From toner cartridge |
| |
|
contacts on the left carousel side plate |
| |
|
to the cable (J512 and J511) that runs to |
| |
|
the high voltage power supply board |
| |
| |
RG5-7130-000CN |
High voltage cable assembly - Connects |
| |
|
between the high voltage board spring |
| |
|
contacts (on the middle frame assembly) |
| |
|
and the cables for the toner cartridge |
| |
|
carousel left plate assembly (J511 and |
| |
|
J512) |
| |
| |
RG5-7145-000CN |
Front cable assembly (six connectors) - |
| |
|
From various components on the front |
| |
|
frame assembly and right side to the DC |
| |
|
controller board |
| |
| |
RG5-7146-000CN |
High voltage cable assembly (two 15-pin |
| |
|
connectors and two 14-pin connectors) - |
| |
|
Connects between the high voltage power |
| |
|
supply board (J501 and J502) and the DC |
| |
|
controller board (J136 and J135) |
| |
| |
RG5-7620-000CN |
Cable assembly (two 5-pin connectors) - |
| |
|
Connects between the DC controller board |
| |
|
(J139) and the fusing assembly drive |
| |
|
motor (J702) |
| |
| |
RG5-7621-000CN |
Cable assembly (two 8-pin connectors) - |
| |
|
Connects between the low voltage power |
| |
|
supply board (J402) and the DC controller |
| |
|
board (J134) |
| |
| |
RG5-7622-000CN |
Upper cable assembly (seven connectors) - |
| |
|
Interconnects various upper level |
| |
|
components to the DC controller board |
| |
| |
RG5-7624-000CN |
Cable assembly (two 3-pin connectors) - |
| |
|
Connects between the waste toner sensor |
| |
|
PC board (J61) and the DC controller |
| |
|
board (J108) |
| |
| |
RH2-5524-000CN |
Flat flexible cable (FFC) assembly - |
| |
|
Connects between the laser/scanner |
| |
|
assembly (J11) the DC controller board |
| |
|
(J102) |
| |
| Cable (Interface) |
C2950A |
IEEE 1284 Bi-Tronics parallel cable - |
| |
|
DB-25 (M) connector (type A) to 36-pin |
| |
|
Centronics (M) connector (type B) - 2.0m |
| |
|
(6.6ft) long |
| |
| |
C2951A |
IEEE-1284 Bi-Tronics parallel cable - |
| |
|
DB-25 (M) connector (type A) to 36 pin |
| |
|
Centronics (M) connector (type B) - 3.0m |
| |
|
(9.8ft) long |
| |
| |
8121-0712 |
Universal Serial Bus (USB) interface |
| |
|
cable - Type 'A' connector to type 'B' |
| |
|
connector - 0.6m (24-inches) long |
| |
| |
C6518A |
Universal serial bus (USB) interface |
| |
|
cable - Type 'A' connector to type 'B' |
| |
|
connector - 2.0m (6.6ft) long |
| |
| Carousel |
RG5-7587-000CN |
Carousel (rotary) assembly - Includes the |
| |
|
carousel assembly, the support assembly, |
| |
|
end plates, drive gears and shaft, |
| |
|
sensors, and cables - Mounts towards the |
| |
|
rear of the printer in front of the rear |
| |
|
frame assembly |
| |
| Cartridge |
Q3960A |
HP Color LaserJet smart Black print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages based on a 5% print density |
| |
| |
Q3961A |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
| |
Q3962A |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
| |
Q3963A |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
| |
Q3971A |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
| |
Q3972A |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
| |
Q3973A |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
| |
Q3960-67901 |
HP Color LaserJet smart Black print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3961-67901 |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3962-67901 |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3963-67901 |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3960-67902 |
HP Color LaserJet smart Black print |
| |
|
cartridge - Will print approximately |
| |
|
5,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3961-67902 |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3962-67902 |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3963-67902 |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
4,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3971-67901 |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages at based on a 5% print |
| |
|
density (not for Europe) |
| |
| |
Q3972-67901 |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3973-67901 |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
|
(not for Europe) |
| |
| |
Q3971-67902 |
HP Color LaserJet smart Cyan print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3972-67902 |
HP Color LaserJet smart Yellow print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| |
Q3973-67902 |
HP Color LaserJet smart Magenta print |
| |
|
cartridge - Will print approximately |
| |
|
2,000 pages based on a 5% print density |
| |
|
(Europe) |
| |
| Clamp |
WT2-5700-000CN |
Cable clamp - White plastic clamp with |
| |
|
mounting pin - Mounts on the upper right |
| |
|
side of the front frame assembly and the |
| |
|
lower left side of the middle frame |
| |
|
assembly (two used) |
| |
| Cleaning Supplies |
5090-3379 |
Toner cleaning cloth - Specially treated |
| |
|
cloth for absorbing toner (1 per package) |
| |
|
Ideal for clening up toner spills |
| |
| Clip |
WT2-5056-000CN |
Cable clip - 'C' shaped White plastic - |
| |
|
Mounts in the opening on the cover for |
| |
|
the paper pickup solenoid |
| |
| |
WT2-5737-000CN |
Cable clip - One mounts on the left side |
| |
|
of the middle frame and two on the base |
| |
|
assembly pan (three used) |
| |
| |
XD2-1100-322CN |
Retainer E-ring clip - Used to secure the |
| |
|
electromagnetic clutch assembly (CL1) on |
| |
|
the paper pickup shaft |
| |
| |
XD2-1100-502CN |
E-ring clip - Secures the dual gear to |
| |
|
the drive shaft which drives the |
| |
|
registration roller - Located on the |
| |
|
inside of the front frame assembly |
| |
| Clutch |
RH7-5366-000CN |
Electromagnetic clutch assembly (24V) - |
| |
|
Electrical clutch between the clutch |
| |
|
drive gear and shaft - (CL1) Engages the |
| |
|
registration roller assembly |
| |
| |
RH7-5335-000CN |
Electromagnetic clutch assembly (24VDC) - |
| |
|
Electrical clutch between the clutch |
| |
|
drive gear and shaft - (CL2) Engages the |
| |
|
roller within the imaging drum/transfer |
| |
|
assembly from the main gear train |
| |
| Connector |
RH2-5519-000CN |
Connector assembly - For optional paper |
| |
|
tray - Mounts to the bottom right side of |
| |
|
the middle frame assembly |
| |
| Control Panel |
RG5-7570-000CN |
Control panel assembly (mechanical only) |
| |
|
- Includes the 'Rotate Carousel', 'Cancel |
| |
|
Job' and the 'Go' buttons, plus the |
| |
|
various indicator light pipes - All |
| |
|
switches and LED's are on the formatter |
| |
|
PC board - Mounts to the top of the right |
| |
|
cover assembly |
| |
| Cover |
RB3-0052-000CN |
Gear Cover (Small Black plastic cover) - |
| |
|
Covers the left end of the feed drive |
| |
|
shaft - Mounts towards the left side of |
| |
|
the middle frame assembly |
| |
| |
RB3-0104-000CN |
Roller cover - Covers the multipurpose |
| |
|
paper pickup roller assembly - Mounts on |
| |
|
the lower front of the front frame |
| |
|
assembly |
| |
| |
RB3-0120-000CN |
Solenoid cover (Steel) - For magnetic |
| |
|
wave sheilding |
| |
| |
RB3-1108-000CN |
Front inner cover (Graphite Black |
| |
|
plastic) - Mounts on the front frame |
| |
|
above the multi-purpose input tray |
| |
| |
RB3-1112-000CN |
Interface bezel (Alloy Gray plastic) - |
| |
|
Vertical cover that surronds the |
| |
|
interface connectors |
| |
| |
RB9-0880-000CN |
Upper rear cover (Alloy Gray plastic) |
| |
| |
RB9-0881-000CN |
Face-down paper output cover (L-Shaped |
| |
|
Graphite Black plastic) - Serves as the |
| |
|
rear of the tray for the face-down output |
| |
|
tray on top of the printer |
| |
| |
RB9-0897-000CN |
Front lower cover (Graphite Black |
| |
|
plastic) - Front lower strip below the |
| |
|
multipurpose input tray - Has recessed |
| |
|
area for the printer logo |
| |
| |
RG5-7567-000CN |
Top cover assembly (Graphite Black |
| |
|
plastic) - Includes the molded-in |
| |
|
face-down output tray and the lift-up top |
| |
|
cover door assembly |
| |
| |
RG5-7569-000CN |
Right side cover assembly (Light Gray |
| |
|
plastic) - Includes the DIMM memory door |
| |
| |
RG5-7571-000CN |
Left side cover assembly (Alloy Gray |
| |
|
plastic) - Includes the power switch |
| |
|
button, rod and spring (The power switch |
| |
|
is located on the low voltage power |
| |
|
supply board) |
| |
| |
RB9-0886-000CN |
Left side cover ONLY (Alloy Gray plastic) |
| |
|
Does not include any attaching parts |
| |
| Damper |
RB2-6248-000CN |
Damper assembly (Gray plastic piece with |
| |
|
small 13-tooth gear on it) - Helps to |
| |
|
reduce clunking when the paper pickup |
| |
|
roller is engaged - Engages the paper |
| |
|
pickup roller - Mounts on the right side |
| |
|
of the front frame assembly |
| |
| Door |
RB9-0884-000CN |
DIMM memory door (Alloy Gray perforated |
| |
|
plastic) - Access door for adding or |
| |
|
removing printer memory or font DIMM - |
| |
|
Mounts on the right side cover |
| |
| |
RF5-4069-000CN |
Top cover door (Graphite Black plastic) - |
| |
|
For accessing the toner cartridges and |
| |
|
the imaging drum/transfer assembly - |
| |
|
Mounts to the top cover frame |
| |
| Drive Assembly |
RG5-7592-000CN |
Rotary drive assembly - Includes the |
| |
|
carousel rotating motor (DCM703), toner |
| |
|
cartridge drive motor (PM705), developing |
| |
|
rotary stopper solenoid (SL93), bracket, |
| |
|
and gears - Mounts on the right top rear |
| |
|
of the print engine |
| |
| Drum |
Q3964-67901 |
Imaging drum/transfer assembly cartridge |
| |
|
Inserts into printer through the top |
| |
|
door - Life expectancy is 20,000 pages |
| |
|
for black print ONLY, 5,000 pages for |
| |
|
color (typical combined life is |
| |
|
approximately 8,000 to 10,000 pages) |
| |
| |
Q3964A |
Imaging drum/transfer assembly cartridge |
| |
|
Inserts into printer through the top |
| |
|
door - Life expectancy is 20,000 pages |
| |
|
for black print only, 5,000 pages for |
| |
|
color (typical combined life is |
| |
|
approximately 8,000 to 10,000 pages) |
| |
| Fan |
RH7-1537-000CN |
Cooling fan (Panaflo Model FBA08T24H - |
| |
|
80mm X 80mm X 15mm high, DC brushless, |
| |
|
24V DC, 190mA) - (FM712) Mounts in the |
| |
|
airflow guide/fan bracket assembly on the |
| |
|
left side of the printer |
| |
| Film (Transparency) |
C2934A |
Color LaserJet transparency film - A size |
| |
|
(8.5 x 11-inches) - 50 sheets per box |
| |
| |
C2936A |
Color LaserJet transparency film - A4 |
| |
|
size (21.0cm x 29.7cm) - 50 sheets per |
| |
|
box |
| |
| Flag |
RB2-9925-000CN |
Sensor arm and flag - Activates the |
| |
|
photosensor (Does NOT include the roller) |
| |
| |
RB3-0111-000CN |
Paper flag - Plastic rod with paper |
| |
|
sensing flag on one end and sensor |
| |
|
activator flag on the other - Senses |
| |
|
paper coming from the multi-purpose front |
| |
|
input tray (tray 1) |
| |
| |
RB3-0135-000CN |
Test print flag (Black lever) - Used to |
| |
|
activate the print engine test switch - |
| |
|
Mounts in a metal holder in the upper |
| |
|
left of the front frame assembly |
| |
| Foot |
RB2-6297-000CN |
Rubber foot - Square self-adhesive rubber |
| |
|
foot - Attaches to the rear of the middle |
| |
|
frame assembly (two used) |
| |
| Fusing Assembly |
RG5-7572-110CN |
Fusing assembly - For 110V to 127V AC |
| |
|
operation - Bonds the toner to the paper |
| |
|
with heat - Slides in and locks in lower |
| |
|
rear of printer |
| |
| |
RG5-7573-000CN |
Fusing assembly - For 220V to 240V AC |
| |
|
operation - Bonds the toner to the paper |
| |
|
with heat - Slides in and locks in lower |
| |
|
rear of printer |
| |
| Gear |
RB3-0022-000CN |
22 tooth gear (Black plastic) - Small |
| |
|
gear with diagonally cut teeth - Idler |
| |
|
gear between the transfer roller assembly |
| |
|
and the feed drive shaft - Mounts on the |
| |
|
left side of the middle frame assembly |
| |
| |
RB3-0091-000CN |
16 tooth gear (Black plastic) - Gear with |
| |
|
large stop tooth and shaft lock tab - |
| |
|
Used as part of the mechanism to |
| |
|
disengage the drive cams for the imaging |
| |
|
drum/transfer assembly - Mounts on the |
| |
|
inside of the right side metal chassis |
| |
|
assembly |
| |
| |
RB3-0092-000CN |
15 tooth gear with drive shaft (Black |
| |
|
plastic) - Used as part of the mechanism |
| |
|
to disengage the drive cams for the |
| |
|
imaging drum/transfer assembly - Mounts |
| |
|
on the right side metal chassis frame |
| |
| |
RS7-0418-000CN |
26 tooth gear (Black plastic) - Has 1/8th |
| |
|
portion of gear cut away - Mounts on the |
| |
|
end of the paper pickup roller for the |
| |
|
multipurpose input tray (Tray 1) |
| |
| |
RS7-0424-000CN |
Dual gear - 20 tooth / 40 tooth - Mounts |
| |
|
between the right side of the front frame |
| |
|
assembly and the paper pickup gear plate |
| |
|
assembly |
| |
| |
RS7-0425-000CN |
30 tooth gear (White plastic) - Part of |
| |
|
the drive gears for the registration |
| |
|
roller - Mounts on inside of the front |
| |
|
frame assembly on the right side |
| |
| |
RS7-0426-000CN |
Dual gear - 26 tooth / 50 tooth (White |
| |
|
plastic) - Part of the drive gears for |
| |
|
the registration roller - Mounts on |
| |
|
inside of the front frame assembly on the |
| |
|
right side |
| |
| |
RS7-0428-000CN |
30 tooth gear (White plastic) - Mounts on |
| |
|
the end of the registration roller drive |
| |
|
shaft |
| |
| |
RS7-0429-000CN |
26 tooth gear (White plastic) - Has |
| |
|
recess for shaft drive pin - Paper pickup |
| |
|
clutch drive gear - Mounts between the |
| |
|
right side of the front fame assembly and |
| |
|
the paper pickup gear plate assembly |
| |
| |
RS7-0435-000CN |
Dual gear - 32 tooth / 37 tooth (White |
| |
|
plastic) - Drives the upper top bin |
| |
|
output roller - Mounts on the right side |
| |
|
of the rear frame assembly |
| |
| |
RS7-0436-000CN |
Dual gear - 37 tooth / 43 tooth (White |
| |
|
plastic) - Part of the gear train for |
| |
|
driving the upper top bin output roller - |
| |
|
Mounts on the right side of the rear |
| |
|
frame assembly |
| |
| |
RS7-0437-000CN |
51 tooth gear (White plastic) - Main |
| |
|
drive gear for both the upper and lower |
| |
|
top bin output rollers |
| |
| |
RS7-0570-000CN |
81 tooth gear - Mounts on a pin on the |
| |
|
right side plate front assembly (between |
| |
|
the gear retaining bracket and the right |
| |
|
side plate) |
| |
| |
RS7-0571-000CN |
Dual gear - 23 tooth / 54 tooth - Small |
| |
|
gear that mounts toward the front on a |
| |
|
short shaft between the gear retainer |
| |
|
bracket and the right side plate front |
| |
|
assembly |
| |
| |
RS7-0572-000CN |
Dual gear - 31 tooth / 90 tooth - Mounts |
| |
|
on a pin on the right side plate front |
| |
|
assembly (between the gear retaining |
| |
|
bracket and the right side plate) |
| |
| |
RS7-0573-000CN |
186 tooth gear - Uppermost large gear |
| |
|
that mounts on a short shaft between the |
| |
|
gear retainer bracket and the right side |
| |
|
plate front assembly |
| |
| |
RS7-0574-000CN |
Dual gear - 32 tooth / 123 tooth - Large |
| |
|
gear which mounts toward the front on the |
| |
|
right side plate front assembly |
| |
| Gear Assembly |
RG5-6938-000CN |
Gear assembly - Metal plate with two |
| |
|
White plastic gears attached - Part of |
| |
|
the drive gears for the paper pickup |
| |
|
roller for the multipurpose input tray |
| |
|
(tray 1) - Mounts on the right side of |
| |
|
the front frame assembly |
| |
| Guide |
RB2-9852-000CN |
Rotary release guide - Small plastic clip |
| |
|
that allows for manual carousel rotation |
| |
|
(with a straightened paper clip) for |
| |
|
removing toner cartridges without power - |
| |
|
Mounts in the top front of the rotary |
| |
|
drive assembly |
| |
| |
RB2-9903-000CN |
Cable guide (Quartz Gray plastic) - |
| |
|
Protects and supports the upper cable |
| |
|
assembly - Mounts to the right rear on |
| |
|
the laser/scanner support assembly |
| |
| |
RB2-9954-000CN |
Left paper feed guide (small Black |
| |
|
plastic arm) - Mounts to the left of the |
| |
|
separation pad assembly on the lower |
| |
|
front frame assembly |
| |
| |
RB2-9955-000CN |
Right paper feed guide (small Black |
| |
|
plastic arm) - Mounts to the right of the |
| |
|
separation pad assembly on the lower |
| |
|
front frame |
| |
| |
RB3-1088-000CN |
Transfer inlet guide assembly - Angled |
| |
|
metal guide between the registration |
| |
|
roller and the transfer roller - Mounts |
| |
|
to the middle frame assembly |
| |
| |
RF5-4065-000CN |
Entrance guide assembly - Mounts in front |
| |
|
of the tranfer roller assembly (behind |
| |
|
the transfer inlet guide) |
| |
| |
RG5-7584-000CN |
Paper guide assembly - Paper width |
| |
|
adjustable guide assembly for the |
| |
|
multipurpose front input tray (tray 1) - |
| |
|
Mounts with the two hinges on the lower |
| |
|
portion of the front frame assembly |
| |
| Hinge |
RB9-0889-000CN |
Tray hinge - 'L' shaped plastic arm - For |
| |
|
the left side of the multi-purpose front |
| |
|
input tray (tray 1) - Mounts in the lower |
| |
|
portion of the front frame assembly |
| |
| |
RB9-0890-000CN |
Tray hinge - 'L' shaped plastic arm - For |
| |
|
the right side of the multipurpose front |
| |
|
input tray (tray 1) - Mounts in the lower |
| |
|
portion of the front frame assembly |
| |
| Holder |
RB2-9924-000CN |
Sensor assembly mounting holder - Holds |
| |
|
the leading edge paper sensor (PS720) for |
| |
|
the fusing assembly - Mounts on the |
| |
|
underside left on the middle frame |
| |
|
assembly |
| |
| |
RB3-0006-000CN |
Holder - Housing for the fusing connector |
| |
|
assembly - Mounts on the lower base pan |
| |
|
of the printer mechanism |
| |
| |
RB3-0023-000CN |
Interlock switch holder (Quartz Gray |
| |
|
plastic) - Does NOT include the |
| |
|
micro-switch - Mounts on the support |
| |
|
shelf for the laser/scanner assembly |
| |
|
(just to the left of the laser/scanner |
| |
|
assembly) |
| |
| Insulator |
RB3-0007-000CN |
Insulating sheet (Transparent plastic) - |
| |
|
Mounts between the bottom pan and the |
| |
|
high and low voltage power supply boards |
| |
| |
RB3-1110-000CN |
Insulating sheet (Transparent plastic) - |
| |
|
For the power supply base assembly - |
| |
|
Mounts to the underside of the middle |
| |
|
frame assembly |
| |
| Interface (Product) |
J3265A |
External JetDirect 500X LAN interface |
| |
|
module - Interfaces up to 3 parallel |
| |
|
printers to an ethernet 10Base-T (RJ-45), |
| |
|
10Base2 (BNC), or 100Base-TX (RJ-45) LAN |
| |
| |
J3258B |
External JetDirect 170X LAN interface |
| |
|
module - Interfaces a parallel printer to |
| |
|
an ethernet 10Base-T (RJ-45) LAN |
| |
| |
J6035C |
HP JetDirect 175X Fast Ethernet external |
| |
|
print server - Has on 4-pin USB connector |
| |
|
and one RJ-45 LAN connector - Connects to |
| |
|
the printer via the USB port and the |
| |
|
network via the LAN port |
| |
| |
J3263A |
External JetDirect 300X LAN interface |
| |
|
module - Interfaces a parallel printer to |
| |
|
an ethernet 10Base-T (RJ-45) or |
| |
|
100Base-TX (RJ-45) LAN |
| |
| |
J6061A |
JetDirect 380X external IEEE-802.11b |
| |
|
(Wi-Fi) wireless print server - Connects |
| |
|
to printer using Universal Serial Bus |
| |
|
(USB) cable |
| |
| |
J7942A |
HP JetDirect en3700 external print server |
| |
|
Fast Ethernet Internet connector for |
| |
|
sharing peripherals with USB ports, in a |
| |
|
10/100 TX LAN environment - Has one USB |
| |
|
2.0 printer port and one RJ-45 10/100 |
| |
|
Base-TX connector - Includes software and |
| |
|
power module |
| |
| Label |
Q2550A |
White full-sheet labels - A size (8.5 x |
| |
|
11-inches) - 25 sheets |
| |
| |
Q2551A |
White full-sheet labels - A size (8.5 x |
| |
|
11-inches) - 100 sheets |
| |
| |
Q2587A |
White labels - 1 x 2.63-inches - 30 |
| |
|
labels per sheet, 25 sheets per box |
| |
| |
Q2588A |
White labels - 1 x 2.63-inches - 30 |
| |
|
labels per sheet, 100 sheets per box |
| |
| |
Q2589A |
White address labels - 1.33 x 4-inches - |
| |
|
14 labels per sheet, 25 sheets per box |
| |
| |
Q2590A |
White address labels - 1.33 x 4-inches - |
| |
|
14 labels per sheet, 100 sheets per box |
| |
| |
Q2591A |
White address labels - 2 x 4-inches - 10 |
| |
|
labels per sheet, 25 sheets per box |
| |
| |
Q2592A |
White address labels - 2 x 4-inches - 10 |
| |
|
labels per sheet, 100 sheets per box |
| |
| |
Q2593A |
White address labels - 0.5 x 1.75-inches |
| |
|
- 80 labels per sheet, 25 sheets per box |
| |
| |
Q2594A |
White address labels - 3.33 x 4-inches - |
| |
|
6 labels per sheet, 100 sheets per box |
| |
| |
RS6-8662-000CN |
Image cartridge label - Shows the imaging |
| |
|
drum/transfer assembly removal steps - |
| |
|
Mounts on the right side of the front |
| |
|
inner cover (Visible when the top cover |
| |
|
is lifted) |
| |
| |
RS6-8668-000CN |
High voltage caution label - Mounts on |
| |
|
the airflow guide / fan bracket assembly |
| |
| Laser/Scanner |
RG5-6880-000CN |
Laser/scanner assembly - Mounts in the |
| |
|
center of the scanner support assembly |
| |
| Manual |
5851-1468 |
LaserJet printer family paper |
| |
|
specification guide |
| |
| Memory (DIMM) |
C7845-67901 |
32MB, 100-pin SDRAM DIMM memory module |
| |
| |
Q1887-67901 |
64MB, 100-pin SDRAM DIMM memory module |
| |
| |
C9121-67901 |
128MB, 100-pin SDRAM DIMM memory module |
| |
| Memory (Product) |
C7845A |
32MB, 100-pin SDRAM DIMM memory module |
| |
| |
Q1887A |
64MB, 100-pin SDRAM DIMM memory module |
| |
| |
C9121A |
128MB, 100-pin SDRAM DIMM memory module |
| |
| Motor |
RF5-4063-000CN |
Main motor assembly - Large motor mounted |
| |
|
on a controller PC board - (DCM701) |
| |
|
Mounts on the inside of the metal right |
| |
|
side frame assembly |
| |
| |
RH7-1628-000CN |
Fusing motor assembly - 24VDC motor |
| |
|
mounted on a motor controller PC board - |
| |
|
(DCM702) Mounts on the right side plate |
| |
|
assembly (next to the DC controller |
| |
|
board) |
| |
| |
RG5-7593-000CN |
Rotary motor assembly - (DCM703) Rotates |
| |
|
the four color toner cartridges in the |
| |
|
carousel to position one of them for |
| |
|
printing |
| |
| |
RH7-1533-000CN |
Stepping motor - 24V DC - (PM704) swings |
| |
|
(or engages) the toner cartridge carousel |
| |
|
in place to transfer toner - Mounts on |
| |
|
the left side of the rear frame assembly |
| |
| |
RH7-1535-000CN |
Stepping motor (24V) - (PM705) used to |
| |
|
drive the internal rollers and mechanisms |
| |
|
in the toner cartridge when it has been |
| |
|
rotated in the printing position on the |
| |
|
carousel |
| |
| Nameplate/Logo |
Q3702-67902 |
LaserJet 2550L Nameplate - Mounts in the |
| |
|
recessed area on the front lower cover |
| |
| PC Board |
Q3702-67901 |
Formatter board assembly - Includes the |
| |
|
formatter board and all the metal cage |
| |
|
covers - Mounts towards the rear on the |
| |
|
metal right frame assembly |
| |
| |
RG5-6964-000CN |
Carousel position and toner level |
| |
|
photoelectric sensor PC board - 'L' |
| |
|
Shaped PC board with the two sensors - |
| |
|
(PS51) Mounts on the left plate in the |
| |
|
toner cartridge carousel assembly |
| |
| |
RG5-6967-000CN |
Registration sensor PC Board - Small |
| |
|
board with flag activated photosensor - |
| |
|
(PS711) Mounts in the registration |
| |
|
assembly on the underside of the middle |
| |
|
frame |
| |
| |
RG5-7607-000CN |
Waste toner sensor assembly PC board - |
| |
|
Detects excess level of waste toner in |
| |
|
the imaging drum/transfer assembly |
| |
|
cartridge - Mounts on the right side of |
| |
|
the front frame assembly |
| |
| |
RG5-7611-030CN |
DC controller board - Mounts on the right |
| |
|
side of the printer (Behind the formatter |
| |
|
board assembly) |
| |
| |
RG5-7612-000CN |
Top of page photoelectric sensor PC board |
| |
|
Includes the photoelectric top of page |
| |
|
sensor and the print engine test switch - |
| |
|
Mounts on the right side of the printer |
| |
|
(Behind the formatter board assembly) |
| |
| |
RH7-7146-000CN |
Density photoelectric sensor PC board - |
| |
|
(PS81) Mounts under the light blocking |
| |
|
pad on the top of the front frame |
| |
|
assembly |
| |
| |
WG8-5382-000CN |
Sensor PC board - Small board with flag |
| |
|
activated photosensor - (PS718) Paper |
| |
|
sensor for the multipurpose tray - Mounts |
| |
|
in the lower right of the front frame |
| |
|
assembly |
| |
| Pad |
RF5-4012-000CN |
Separation pad assembly - Includes the |
| |
|
separation pad, holder and spring - |
| |
|
Mounts below the multipurpose front input |
| |
|
(Tray 1) pickup roller assembly |
| |
| |
RF5-4047-000CN |
Light blocking pad assembly - Black |
| |
|
plastic frame with soft rubber gasket and |
| |
|
stiff conductive Mylar piece (grounded) - |
| |
|
Mounts to the top center of the front |
| |
|
frame assembly |
| |
| Paper |
Q1298A |
LaserJet Satin finish tough paper - A |
| |
|
size (8.5 x 11-inches) - Will not tear |
| |
|
and will withstand outdoor weather |
| |
|
conditions - Can print on both sides |
| |
| |
Q1298B |
LaserJet Satin finish tough paper - A4 |
| |
|
size (21.0cm x 29.7cm) - Will not tear |
| |
|
and will withstand outdoor weather |
| |
|
conditions - Can print on both sides - 50 |
| |
|
sheets per box |
| |
| |
Q2413A |
Premium LaserJet cover paper - |
| |
|
Heavyweight (75lb), smooth finish on both |
| |
|
sides, 96 brightness - A size (8.5 x |
| |
|
11-inches) - 100 sheets per box |
| |
| Paper (Glossy) |
Q2415A |
Soft gloss LaserJet paper - Soft gloss |
| |
|
finish on both sides, 95 brightness - A |
| |
|
size (8.5 x 11-inches) - 500 sheets per |
| |
|
box |
| |
| |
Q2417A |
Soft gloss LaserJet paper - Soft gloss |
| |
|
finish on both sides, 95 brightness - A4 |
| |
|
size (21.0cm x 29.7cm) - 250 sheets per |
| |
|
box |
| |
| |
Q6541A |
Soft gloss, bright white LaserJet paper - |
| |
|
A size (8.5 x 11-inches) - 200 sheets per |
| |
|
box |
| |
| |
Q6542A |
Soft gloss, bright white LaserJet paper - |
| |
|
A4 size (21.0cm x 29.7cm) - 200 sheets |
| |
|
per box |
| |
| |
Q6545A |
Glossy LaserJet paper - Gloss finish on |
| |
|
both sides, 95 brightness - A size (8.5 x |
| |
|
11-inches) - 200 sheets per box |
| |
| |
Q6547A |
Glossy LaserJet paper - Gloss finish on |
| |
|
both sides, 95 brightness - A4 size |
| |
|
(21.0cm x 29.7cm) - 200 sheets per box |
| |
| Paper (Matte) |
Q6543A |
Matte brochure (Heavyweight) laser paper |
| |
|
- A size (8.5 x 11-inches) - 150 sheets |
| |
|
per box |
| |
| |
Q6544A |
Matte brochure (Heavyweight) laser paper |
| |
|
- A4 size (21.0cm x 29.7cm) - 150 sheets |
| |
|
per box |
| |
| |
Q6549A |
Photo and imaging LaserJet paper - Matte |
| |
|
finish on both sides, 96 brightness - A |
| |
|
size (8.5 x 11-inches) - 100 sheets per |
| |
|
box |
| |
| |
Q6550A |
Photo and imaging LaserJet paper - Matte |
| |
|
finish on both sides, 96 brightness - A4 |
| |
|
size (21.0cm x 29.7cm) - 100 sheets per |
| |
|
box |
| |
| Plate |
RB2-9916-000CN |
Mounting/grounding plate - For the |
| |
|
engaging motor (PM704) - Mounts on the |
| |
|
upper left side of the rear frame |
| |
|
assembly |
| |
| |
RB3-0057-000CN |
Transfer slide plate - Small 'U' shaped |
| |
|
metal insert plates - Mount in the |
| |
|
bushing wells for the transfer roller on |
| |
|
the middle frame assembly (two used) |
| |
| |
RB3-0065-000CN |
Contact plate - copper clad metal spring |
| |
|
- Holds the left end of the small 500 |
| |
|
Meg-ohm resistor |
| |
| |
RB3-0066-000CN |
Contact plate - copper clad metal spring |
| |
|
- Holds the right end of the small 500 |
| |
|
Meg-ohm resistor - Mounts on the left |
| |
|
side of the middle frame below the |
| |
|
entrance guide assembly |
| |
| |
RB3-0286-000CN |
Contact plate - Runs between the shaft on |
| |
|
the registration roller and the metal |
| |
|
entrance guide assembly |
| |
| |
RB3-1113-000CN |
Grounding plate - Small plate with |
| |
|
grounding finger - Grounds the end of the |
| |
|
carousel drive shaft - Mounts towards the |
| |
|
top on the left side plate assembly |
| |
| Power Cord |
8120-6809 |
Power cord (Dove Gray) - 2.3m (7.5ft) |
| |
|
long - Has straight (F) receptacle (for |
| |
|
240V in the United Kingdom, Hong Kong, |
| |
|
Singapore, Malaysia) |
| |
| |
8120-6810 |
Power cord (Flint Gray) - 2.3m (7.5ft) |
| |
|
long - Has straight (F) C13 receptacle |
| |
|
(for 240V in Australia and New Zealand) |
| |
| |
8120-6811 |
Power cord (Flint Gray) - 17 AWG, 2.3m |
| |
|
(7.5ft) long - Has straight (F) C13 |
| |
|
receptacle (for 220V in Europe, Saudi |
| |
|
Arabia, South Africa, India, and Korea) |
| |
| |
8120-6812 |
Power cord (Flint Gray) - 18 AWG, 2.3m |
| |
|
(7.5ft) long - Has straight (F) |
| |
|
receptacle (for 120V in the USA, Canada, |
| |
|
Mexico, Philippines, and Taiwan) |
| |
| |
8120-6813 |
Power cord (Flint Gray) - 17 AWG, 2.3m |
| |
|
(7.5ft) long - Has straight (F) |
| |
|
receptacle (for 220V in South Africa, |
| |
|
Saudi Arabia, and India) |
| |
| |
8120-6814 |
Power cord (Flint Gray) - 17 AWG, 2.3m |
| |
|
(7.5ft) long - Has straight (F) |
| |
|
receptacle (for 220V in Denmark) |
| |
| |
8120-6815 |
Power cord (Flint Gray) - 17 AWG, 2.3m |
| |
|
(7.5ft) long - Has straight (F) |
| |
|
receptacle (for 220V in Switzerland) |
| |
| Power Supply |
RG5-7124-000CN |
Sub-high voltage board - Small auxillary |
| |
|
PC board - Mounts in a holder just above |
| |
|
the high voltage board in the bottom pan |
| |
|
assembly |
| |
| |
RG5-7606-000CN |
High voltage power supply board (HVT) |
| |
|
assembly - Has contacts for the eight |
| |
|
high voltage springs in the printer - |
| |
|
Mounts in the bottom pan assembly |
| |
|
(Towards the front of the printer) |
| |
| |
RH3-2262-000CN |
Low voltage power supply - For 110VAC to |
| |
|
127VAC operation - Includes the AC power |
| |
|
input connector and power switch - Mounts |
| |
|
in the bottom pan assembly towards the |
| |
|
rear of the printer |
| |
| |
RH3-2263-000CN |
Low voltage power supply - For 220VAC to |
| |
|
240VAC operation - Includes the AC power |
| |
|
input connector and power switch - Mounts |
| |
|
in the bottom pan assembly towards the |
| |
|
rear of the printer |
| |
| Pressure Assembly |
RG5-7589-000CN |
Carousel pressure (support) assembly - |
| |
|
Includes the main rear support, E-label |
| |
|
reader assembly, engaging sensor, and the |
| |
|
engaging rod shaft - Primary support |
| |
|
structure for the toner cartridge |
| |
|
carousel |
| |
| Pulley |
RB3-0061-000CN |
Pulley roller (accommodates three feed |
| |
|
belts) - Small black roller approximately |
| |
|
3.49cm (1-3/4 inches) long with three |
| |
|
ball type pulleys - Mounts just behind |
| |
|
the transfer roller in the middle frame |
| |
|
assembly (two used) |
| |
| |
RB3-0067-000CN |
Pulley roller (accommodates one feed |
| |
|
belt) - Small black roller approximately |
| |
|
1.59cm (5/8 inch) long with one ball type |
| |
|
pulley - Mounts just behind the transfer |
| |
|
roller in the middle frame assembly (two |
| |
|
used) |
| |
| Rack Slide |
RB3-0090-000CN |
Rack slide - White plastic piece with |
| |
|
gear teeth layed out in rack form on both |
| |
|
sides - Part of the mechanism that |
| |
|
disengages the imaging drum/transfer |
| |
|
assembly cams when the top cover is |
| |
|
opened - Mounts vertically on the metal |
| |
|
right side frame |
| |
| Reader |
RG5-6956-000CN |
E-label reader (contact board ONLY) - |
| |
|
Connects the cartridge nonvoliatile |
| |
|
memory to the DC controller board - For |
| |
|
the imaging drum/tranfer assembly - |
| |
|
Mounts to the the front frame assembly |
| |
| |
RG5-6957-000CN |
E-label reader assembly - Connects |
| |
|
cartridge nonvoliatile memory to the DC |
| |
|
controller board - For the toner |
| |
|
cartridges - Mounts on top of the toner |
| |
|
cartridge carousel assembly |
| |
| Resistor |
RH5-3115-000CN |
500 Meg-ohm, 300mW - Mounts on the left |
| |
|
side of the middle frame below the |
| |
|
entrance guide assembly - Held in place |
| |
|
with two small contact plates |
| |
| Rod |
RB3-0037-000CN |
Power switch rod - Goes between the power |
| |
|
button and the power switch on the low |
| |
|
voltage power supply board - Mounts on |
| |
|
the left side cover |
| |
| Roller |
RB2-7195-000CN |
Sensor flag roller (small White plastic |
| |
|
roller) - Mounts in the sensor arm flag |
| |
|
for the leading edge paper sensor for the |
| |
|
fusing assembly (PS720) |
| |
| |
RB2-9909-000CN |
Pressure roller (small Black hard plastic |
| |
|
'solid' roller) - Presses against the |
| |
|
lower top bin output roller on the middle |
| |
|
rear of the printer (two used) |
| |
| |
RB3-0012-000CN |
Belt roller - Small oval shaped roller |
| |
|
approximately 1-3/4 inches long - Mounts |
| |
|
toward the center of the metal feed plate |
| |
|
on the middle frame assembly |
| |
| |
RB3-0160-000CN |
Paper pickup roller ('D' shaped) - Mounts |
| |
|
on the paper pickup roller assembly for |
| |
|
the multipurpose front input tray (tray |
| |
|
1) |
| |
| Roller Assembly |
RF5-4067-030CN |
Transfer roller assembly - Long black |
| |
|
foam type roller - Transfers static |
| |
|
charge to paper - Mounts towards the |
| |
|
front and on top of the middle frame |
| |
|
assembly |
| |
| |
RG5-6897-020CN |
Upper top bin output roller assembly - |
| |
|
Includes the shaft with four rubber |
| |
|
rollers, two bushing/shaft retainers, two |
| |
|
anti-reversing flaps, and the drive gear |
| |
|
Mounts on the top rear of the printer |
| |
| |
RG5-6939-020CN |
Registration roller assembly - Includes |
| |
|
the roller, bushings, mounting plate, |
| |
|
paper sensor, and the sensor flag - |
| |
|
Mounts from the bottom toward the front |
| |
|
center of the middle frame assembly |
| |
| |
RG5-6952-000CN |
Paper pickup roller assembly - Includes |
| |
|
the shaft, guide assembly cams, the |
| |
|
D-shaped roller, and roller retainers - |
| |
|
Picks paper from the multipurpose front |
| |
|
input tray (tray 1) - Mounts in the lower |
| |
|
portion of the front frame assembly |
| |
| |
RG5-7595-000CN |
Lower top bin output roller assembly - |
| |
|
Includes the shaft with four rubber |
| |
|
rollers, two bushing/shaft retainers, and |
| |
|
the drive gear - Mounts in the center on |
| |
|
the rear frame assembly (above the fusing |
| |
|
assembly) |
| |
| Screw |
XA9-0849-000CN |
M3 truss-head phillips screw with machine |
| |
|
threads - 6mm long - Primarily used to |
| |
|
secure metal to metal parts |
| |
| |
XA9-0890-000CN |
M3 truss-head phillips screw with machine |
| |
|
threads - 6mm long - Primarily used to |
| |
|
secure metal to metal parts |
| |
| |
XA9-1262-000CN |
M4 pan-head phillips screw with |
| |
|
self-tapping threads - 10mm long - Used |
| |
|
primarily to secure metal parts to the |
| |
|
internal plastic frames |
| |
| |
| |
XA9-1291-000CN |
M3 pan-head phillips screw with flat |
| |
|
washer - 8mm long - Secures the side |
| |
|
covers to the printer mechanism and one |
| |
|
is used to secure the fusing assembly |
| |
|
connector holder to the bottom pan |
| |
| |
XA9-1328-000CN |
M3 pan-head phillips screw - 10mm long - |
| |
|
Used to secure the fusing assembly drive |
| |
|
motor to the right side plate |
| |
| |
XA9-1355-000CN |
M3 pan-head phillips screw with machine |
| |
|
threads - 8mm long - Used to secure the |
| |
|
thermistor to the right side plate and |
| |
|
the power supply PC boards the the base |
| |
|
assembly pan |
| |
| Shaft |
RB3-0011-000CN |
Feed drive shaft - Long shaft with eight |
| |
|
feed belt ball type pulleys and one |
| |
|
ribbed feed guide drive belt pulley - |
| |
|
Mounts behind the transfer roller on the |
| |
|
middle frame assembly |
| |
| |
RB3-0060-020CN |
Idler gear shaft - Short metal rod - |
| |
|
Shaft for the transfer and feed drive |
| |
|
idler roller - Mounts on the left side of |
| |
|
the middle frame assembly |
| |
| Shield |
RB2-9932-000CN |
RFI shield - Parallel wire form mounted |
| |
|
over the fan - Mounts on the fan air duct |
| |
|
assembly on the left side of the printer |
| |
| Shutter |
RG5-6940-050CN |
Registration shutter assembly - Includes |
| |
|
the metal roller, mounting frame, |
| |
|
grounding springs, and the dual coupling |
| |
|
gear - Mounts over the registration |
| |
|
roller at the front of the middle frame |
| |
|
assembly |
| |
| Sideplate |
RG5-6942-000CN |
Left side carousel plate assembly - End |
| |
|
plate under the rotational toner |
| |
|
cartridge carousel - Includes all of the |
| |
|
high voltage contacts for the toner |
| |
|
cartridges - Mounts on the metal carousel |
| |
|
support frame |
| |
| |
RG5-7579-000CN |
Main drive (right side plate) assembly - |
| |
|
Includes the right side plate front |
| |
|
assembly (with main motor, clutch, and |
| |
|
gears) and the right side plate rear |
| |
|
assembly (with drive gears) - Mounts on |
| |
|
the right side |
| |
| |
RG5-7580-000CN |
Right side plate rear assembly - Includes |
| |
|
the rear half of the metal right side |
| |
|
plate and the two associated gears - |
| |
|
Mounts on rear half of right side of |
| |
|
printer |
| |
| |
RG5-7581-000CN |
Right side plate front assembly - |
| |
|
Includes the front half of the metal |
| |
|
frame assembly, gears, imaging |
| |
|
drum/transfer assembly drive cams, cover |
| |
|
engaging mechanism, roller engaging |
| |
|
clutch (CL2), and main drive motor |
| |
|
(DCM701) - Mounts on the right side |
| |
| Solenoid |
RH7-5338-000CN |
Solenoid assembly - (SL92) Lever on the |
| |
|
solenoid disengages the stop on the drive |
| |
|
gear on the paper pickup roller for the |
| |
|
multipurpose input tray (tray 1) |
| |
| |
RH7-5340-000CN |
Solenoid assembly - (SL93) Engages to |
| |
|
stop rotation when the proper toner |
| |
|
cartridge on the carousel is in place for |
| |
|
printing |
| |
| Spring |
RB2-9905-000CN |
Torsion spring - Provides pressure for |
| |
|
the upper top bin output pressure rollers |
| |
|
(two used) |
| |
| |
RB2-9952-000CN |
Tray 1 flag spring - Provides torsion for |
| |
|
the tray 1 paper sensor flag - Mounts in |
| |
|
the lower portion of the front frame |
| |
|
assembly |
| |
| |
RB2-9999-000CN |
Torsion spring - Secures the belt roller |
| |
|
(for the feed drive shaft) in the top of |
| |
|
the middle frame assembly |
| |
| |
RB3-0015-000CN |
Compression spring - Provides upward |
| |
|
pressure for the left transfer roller |
| |
|
bushing |
| |
| |
RB3-0016-000CN |
Electrical contact spring - Spring steel |
| |
|
wire with compression springs formed on |
| |
|
both ends - One end provides upward |
| |
|
pressure on the right bushing for the |
| |
|
transfer roller - Connects to high |
| |
|
voltage board |
| |
| |
RB3-0042-000CN |
Electrical contact spring - Mounts on the |
| |
|
middle frame assembly behind the transfer |
| |
|
roller - Of the four similar springs, |
| |
|
this one is next to the one on the far |
| |
|
left - Connects to high voltage board |
| |
| |
RB3-0043-000CN |
Electrical contact spring - Mounts on the |
| |
|
middle frame assembly behind the transfer |
| |
|
roller - Of the four similar springs, |
| |
|
this one is on the far right - Connects |
| |
|
to high voltage board |
| |
| |
RB3-0044-000CN |
Electrical contact spring - (Front) |
| |
|
Provides high voltage to the toner |
| |
|
cartridge via a cable assembly and |
| |
|
connection through the carousel plate |
| |
|
assembly - Connects to the high voltage |
| |
|
board |
| |
| |
RB3-0045-000CN |
Electrical contact spring - Rear |
| |
|
electrical contact spring - Provides high |
| |
|
voltage to the toner cartridge via a |
| |
|
cable assembly and connection through the |
| |
|
carousel plate assembly - Connects to the |
| |
|
high voltage board |
| |
| |
RB3-0046-000CN |
Electrical contact spring - Mounts on the |
| |
|
middle frame assembly behind the transfer |
| |
|
roller - Of the four similar springs, |
| |
|
this one is just to the left of the one |
| |
|
on the far right - Connects to high |
| |
|
voltage board |
| |
| |
RB3-0047-000CN |
Electrical contact spring - Mounts on the |
| |
|
underside of the middle frame assembly - |
| |
|
Connects to high voltage board |
| |
| |
RB3-0048-000CN |
Electrical contact spring - Mounts on the |
| |
|
middle frame assembly behind the transfer |
| |
|
roller - Of the four similar springs, |
| |
|
this one is on the far left - Connects to |
| |
|
the high voltage board |
| |
| |
RB3-0121-000CN |
Right retaining spring - Helps to secure |
| |
|
and ground the imaging drum/transfer |
| |
|
assembly in the printer - Mounts on the |
| |
|
upper right side of the front frame |
| |
|
assembly |
| |
| |
RB3-0122-000CN |
Left retaining spring - Helps to secure |
| |
|
the imaging drum/transfer assembly in the |
| |
|
printer - Mounts on the upper left side |
| |
|
of the front frame assembly |
| |
| |
RB3-1065-000CN |
Torsion spring - Provides pressure for |
| |
|
the lower top bin output pressure rollers |
| |
|
(two used) |
| |
| |
RS6-2030-000CN |
Tension spring - Provides support tension |
| |
|
for the multipurpose front input tray |
| |
|
guide assembly (two used) |
| |
| |
RS6-2759-000CN |
Compression spring - Provides tension for |
| |
|
the power switch button - Mounts on the |
| |
|
left side cover |
| |
| |
RS6-2766-000CN |
Tension spring - Provides a small amount |
| |
|
of return tension for the sensor flag arm |
| |
|
on the leading edge sensor for the fusing |
| |
|
assembly (PS720) |
| |
| Standoff |
VT2-0012-005CN |
PC Board support - Plastic standoff for |
| |
|
supporting a PC board - Supports the high |
| |
|
voltage board on the base assembly metal |
| |
|
pan (six used) |
| |
| Static Dissipater |
RB3-0009-000CN |
Static eliminator ground plate - Right |
| |
|
angled metal piece with small teeth on |
| |
|
top edge - Mounts from underneath on the |
| |
|
middle frame assembly just behind the |
| |
|
pulley rollers |
| |
| Support |
RB3-0062-000CN |
PC board support (Black plastic holder) - |
| |
|
For mounting the small sub-high voltage |
| |
|
board above the high voltage board |
| |
| |
RG5-6907-030CN |
Laser/scanner support assembly (sheet |
| |
|
metal plate) - Crossmember between the |
| |
|
two side frames - Support for the |
| |
|
laser/scanner assembly, the toner |
| |
|
cartridge carousel drive motor, and the |
| |
|
cover interlock switch assembly |
| |
| Switch |
RH7-6051-000CN |
Microswitch with lever activator - (SW2) |
| |
|
Senses when the top cover is open - |
| |
|
Mounts in a holder on the scanner support |
| |
|
assembly |
| |
| Thermistor |
RH7-7149-000CN |
Thermistor - (TH3) For detecting internal |
| |
|
temperature - Mounts to the metal right |
| |
|
side frame assembly just above the DC |
| |
|
controller board |
| |
| Tray |
Q3709-67901 |
Replacement 250-sheet paper input feeder |
| |
|
assembly - Includes tray base which |
| |
|
attaches to printer, and the paper |
| |
|
cassette tray - Accommodates 148mm x |
| |
|
210mm (5.8 x 8.3 inches) to 216mm x 356mm |
| |
|
(8.5 x 14 inches) media - Only one |
| |
|
250-sheet feeder supported |
| |
| |
Q3709A |
Optional 250 sheet paper input tray - |
| |
|
Includes tray base which attaches to |
| |
|
printer, and the slide out paper tray - |
| |
|
Accommodates 148mm x 210mm (5.8 x 8.3 |
| |
|
inches) to 216mm x 356mm (8.5 x 14 |
| |
|
inches) media - Only one 250 sheet tray |
| |
|
supported per printer |
| |
| |
Q3710-67901 |
Replacement optional 500-sheet paper |
| |
|
feeder assembly - Includes feeder base |
| |
|
which attaches to tray 2, and the slide |
| |
|
out paper tray - Note that the optional |
| |
|
250-sheet feeder assembly must be |
| |
|
installed first - (Part of Q3710A) |
| |
| |
Q3710A |
Optional 500 sheet paper feeder assembly |
| |
|
Includes the feeder base which attaches |
| |
|
to tray 2, and slide out paper tray - |
| |
|
Accommodates 216mm x 279mm (8.5 x 11in) |
| |
|
or 210mm x 279mm (8.3 x 11.7in) media - |
| |
|
Optional 250 sheet feeder must be |
| |
|
installed first |
| |
| |
RB3-0019-000CN |
Toner catch tray (curved Black plastic |
| |
|
piece) - Holds residual toner from |
| |
|
photosensitive drum - Mounts just below |
| |
|
the toner cartridge carousel on the |
| |
|
bottom frame assembly |
| |
| Tray Assembly |
RG5-7585-000CN |
Multipurpose front input tray assembly |
| |
|
(tray 1) - Includes the front cover |
| |
|
piece, pull-out paper support, and the |
| |
|
flip-out extender - Mounts on front of |
| |
|
printer (on the front frame assembly) |
| |
| Tray Kit |
C9706-67901 |
Multipurpose tray (tray 1) service kit - |
| |
|
Includes one paper pickup roller and one |
| |
|
separation pad assembly |
| |
| |
C9706-67902 |
Multipurpose tray (tray 1) service kit |
| |
|
with extra separation pads - Includes one |
| |
|
paper pickup roller and three separation |
| |
|
pad assembly |
Login Here
