|
|
|
How
to Reset the Maintenance Counter Message |
| 
LaserJet 4000/4050/4100
|
LaserJet 5000/5100 |
Reset
at: (200,000 pages)
1. Shut printer off. (Use
the SHUT OFF switch)
2. Hold down the Left Side of the ITEM and
VALUE Buttons while powering the Printer back on.
3. Continue to hold the Buttons until the Printer
says “RESET MAINTENANCE COUNTER” then release
the Buttons.
Click
Here For Printer Friendly Version |
Reset
at: (150,000 pages)
1.
Shut the Printer off. (Use the shut off switch)
2. Hold down the Left Side of the ITEM and
VALUE Buttons while powering the Printer back on.
3. Continue to hold Buttons until the Printer
says “RESET MAINTENANCE COUNTER”, Then release
the Buttons.
Click Here For
Printer Friendly Version |
|
LaserJet 9000/9050 |
LaserJet 5si |
Reset at: (350,000 pages)
1. Power off the Printer.
2. Press and hold the CHECK “? “ Button
located on the center of the display.
3. Now power the Printer on while pressing the CHECK
(?) Button.
4. Now hold the CHECK (?) for at least 3-4 seconds,
then release the Button.
5. Now you will see a Select Language prompt on your
Printers Display.
6. Now press the QUESTION MARK (?)Button.
7. Now the MAINTENANCE KIT will be displayed.
8. Now press the CHECK (?)Button and you are finished.
Click
Here For Printer Friendly Version |
Reset
at: (350,000 pages)
1. Turn the Printer Offline.
2. Press the MENU Button until Configuration
Menu is displayed.
3. At this time press the ITEM Button one
(1) time.
4. (Service Message = Off ) will be displayed.
5. Now press the SELECT Button.
6. Now press the ONLINE Button.
7. Now you are finished.
Click
Here For Printer Friendly Version |
|
LaserJet 8000/8100/8150 |
LaserJet 4200/4300 |
Reset
at: (350,000 pages)
1. To access the Service Mode, power the
Printer down/off and hold down the SELECT & JOB CANCEL
Buttons.
2. Power the Printer back on while holding
these two (2) Buttons.
3. Hold these Buttons for at least 4 seconds
then release.
4. Now press the MENU & SELECT Buttons.
5. You should see “SERVICE MODE”
in the display.
6. The Printer will cycle, This is normal.
7. Now press the MENU Button, Then the SERVICE
MENU will be displayed on your printer.
8. Now press the ITEM Button until “MAINTCOUNT”
is on the display.
9. Now use the + or – Buttons to change
the numbers to 0’s.
10. Now press the SELECT Button.
11. Now an Asterisk (*) will appear and you
are finished.
12. To exit the Service Mode press the GO
Button.
Click Here For Printer
Friendly Version |
Reset
at: (200,000 pages)
1. Use the following Pin
Codes:
For LaserJet 4200 (11420002)
For LaserJet 4300 (11430002)
2. Press the SELECT Button to open the
Menus.
3. Now use the UP Arrow or DOWN Arrow Buttons
to scroll to SERVICE.
4. Once at SERVICE, Press the SELECT Button.
5. Now press the UP or DOWN Arrow Buttons
until the first digit of the Pin Code appears.
6. Now press the SELECT Button to save
that digit.
7. Repeat this selection procedure until
the entire eight (8) digit Pin Code is saved.
8. The Service Sub Menu will appear on
the display of the Printer.
9. Now use the UP and DOWN Arrows to scroll
to the Maintenance Item on the Service Sub Menu and press
the SELECT Button.
10. Now you can set the number of pages
since the last Maintenance Kit was installed.
11. The printer automatically exits the
Service Menu after about one (1) minute if no Buttons are
pressed. You can also hit the PAUSE/RESUME Button to exit.
Click Here For Printer Friendly Version
|
|
|
Chris
Cole
Certified
Technician
CEO/President
Feedroller.com
was created for
you the Printer
Owner, to Repair
your Printer with
Technician
Confidence.
|
|
Morgan
Anderson
Certified
Technician
Do you have a Printer problem?
Talk with our
Technician's were
happy to help.
|
|
Josh
Henry
Certified
Technician
I Guarantee you
will receive the
Best selection of
Parts available.
|
|
Chris
Kurczyk
Warehouse
Manager
If you have any
Questions or
Concerns about
your Order,
Contact us
for help. |
|
